This kit allows you to mount any device with a ¼ 20” (or 3/8 16”with ¼ 20” to 3/8 16” adapter) screw hole, such as an external on-board monitor, lights, and/or hard drives, using a Zamerican Arm. The arm is mounted on a set of 19mm Studio rods using the q-mount.

This kit allows you to mount any device with a ¼ 20” (or 3/8 16”with ¼ 20” to 3/8 16” adapter) screw hole, such as an external on-board monitor, lights, and/or hard drives, using a Zamerican Arm. The arm is mounted on a Zicromount III that is attached to your camera's handle. The Zicromount III prevents unwinding with the use of the L prongs.

This kit allows you to mount any device with a ¼ 20” (or 3/8 16”with ¼ 20” to 3/8 16” adapter) screw hole, such as an external on-board monitor, lights, and/or hard drives, using a Zamerican Arm. The arm is mounted on a Zicromount III that is attached to your camera's handle. The Zicromount III prevents unwinding with the use of the L prongs.

The Zonitor Handheld mount kit allows you to quick-release a monitor from a Zamerican articulating arm and the arm from the Zacuto 15mm Z-Mount or 19mm Zandy. This kit allows you to mount any device with a ¼ 20” (or 3/8 16”with ¼ 20” to 3/8 16” adapter) screw hole, such as an external on-board monitor, lights, and/or hard drives, using a Zamerican Arm. The arm is mounted on one rod using a Zacuto 15mm Z-Mount or 19mm Zandy (please select below).

This kit allows you to mount any device with a ¼ 20” (or 3/8 16”with ¼ 20” to 3/8 16” adapter)screw hole, such as an external on-board monitor, lights, and/or hard drives, using a Zamerican Arm. The arm is mounted on a set of 15mm lightweight rods using the q-mount.

The Zotshoe connects to the shoe of the camera, and it is taped 1/4 20.

This EVF mount is the mount all RED users have been waiting for. It is inexpensive, adjustable and will not loosen. The mount slides onto the top 19mm or 15mm rod on the RED ONE camera. If sliding this mount onto a 15mm rod, a Z-mount will be needed instead of a Zandy. It has a rod end cap at the end of the rod so the EVF can not accidently slide off the rod. This mount has the ability to slide the EVF forward and backward as well as a complete 360 degree swivel for top or bottom or ENG use.

The Zred Zwivel is the new addition to our already popular Zred mount. The Zred Zwivel gives you more adjustability and movement for your RED EVF. The mount slides onto the top 19mm or 15mm rod on your RED ONE camera. The Zred Zwivel mounts one of two ways. If your top rod is 15mm you will get the Z-Mount., if it is 19mm then you will need the Zandy. You will make this selection at checkout. This Zred Zwivel has the ability to slide the EVF forward and backward, up and down as well as a complete 360 degree swivel, left and right, up and down.

The Zround Mount is a retrofit to allow Zacuto DoubleMounts and MiniMounts to accept Z-Release Zamerican arm or ZUDS. ZUDs convert your 1/4 20", 3/8 16" screws to 15mm rods, thus allowing them to fit into Z-Mounts, 15mm Z-Locks, ZicroMounts and all other Zacuto 15mm locking devices. This gives quick release action to your Zacuto DoubleMount or MiniMount. The Zround Mount comes with a 3/8 16".

The Ztudio is a z-release mount that allows you to mount a 19mm rod perpendicular to another 19mm rod.